Author Topic: DIY door lining to reduce wind noise: who's interested?  (Read 198449 times)

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #140 on: December 21, 2006, 11:53:15 AM »
You are absolutely right. 10 buck worth of tape can only do 4 doors mah, what to do.  :D :D

Anyway, a more detailed description of the closing door effect.

With the tape pasted onto the frame,
Front door - Hard to close, easier now after it becomes seasoned.
Rear door - A little harder to close than before only. Was quite surprise that it wasn't like the front door.

With tape pasted onto the door,
Front door - Much easier to close as compared to the above method. It also looks nicer as the tape is concealed with the original rubber. The vacuum effect is still there, but I dun have the chance to verify if this method is better that the former in terms of sound proofing.
Rear door - Same as front door.

personally, I prefer the second method. Cleaner and better looking. Based on what I see, if you have 10 more bucks to spare, it is possible to do both method on the same door.

good fr bro.  :thumbsup:  :D think when i redo my car i also gonna stick it onto the door itself to try le.  :D


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #141 on: December 21, 2006, 11:54:14 AM »
Recently noticed that my rear doors when opening got this 'muack muack' sound, sounds like rubbers rubbing against each other sound. Guess its the new door lining rubbing against the original lining. Think its because I did't stick the door lining properly. If the findings from the bros here is that its better to stick on the door itself, then maybe a buy one more roll and do it on the door and take out the one on the frame, $10 and 30min only ma...  :D

haha. anytime u wan bro, just leave me a msg, then maybe can have that delicious chao tao kuay again.  :D


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline blackspotGG

  • Low End (2000 rpm)
  • **
  • Posts: 291
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #142 on: December 21, 2006, 12:09:25 PM »
haha. anytime u wan bro, just leave me a msg, then maybe can have that delicious chao tao kuay again.  :D

Too bad rubber have shelf life, else I'll buy 2-3 to stock up, anytime the current one not so good liao can change, muahahahhahahaha....

Chai Tow kuay? No need to wait till DIY session, if you coming on any sunday morning can SMS me, cos that's normally my breakfast for sunday. Also if any DIY can come to my MSCP, big, bright, windy, got shops and coffee shop below the MSCP...  ;D

Offline Leapin_Toufu

  • Cool Engine (0 rpm)
  • Posts: 48
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #143 on: December 21, 2006, 05:20:52 PM »
These are the people who have put their names down and still havent collected. Pls contact me to fix a collection time and place k? 

1. Laguna968 - collecting another day
2. alezis - collecting another day
3. optoms - collecting another day

These are the people who have allocated their interest. Prices still at $10

1. undercover 
2. revin81
3. teo_jason - 98790334
4. Leapin_Toufu (9-8-5-5-5-1-9-1)
5.

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #144 on: December 21, 2006, 09:38:58 PM »
These are the people who have put their names down and still havent collected. Pls contact me to fix a collection time and place k? 

1. Laguna968 - collecting another day
2. alezis - collecting another day
3. undercover
4. Revin81

These are the people who have allocated their interest. Prices still at $10  :thumbsup:

1. teo_jason - 98790334
2. Leapin_Toufu (9-8-5-5-5-1-9-1)
3.
4.
5.
« Last Edit: December 21, 2006, 11:00:32 PM by corgan »


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #145 on: December 21, 2006, 10:58:49 PM »
Hi people. Due to some unforeseen circumstances  :D , I have of now 4 pieces left, 2 for ALezis and Laguna and the other 2 for the first 2 people who have indicated their interest which are Bro undercover and revin81.


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

optoms

  • Guest
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #146 on: December 21, 2006, 10:59:53 PM »
hi corgan, think i need to get from u another roll cos i really messed up the installation. cut and paste , cut and paste.  :mad: Some linnings came off...... I will redo it again... :nonod:

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #147 on: December 21, 2006, 11:14:01 PM »
hi corgan, think i need to get from u another roll cos i really messed up the installation. cut and paste , cut and paste.  :mad: Some linnings came off...... I will redo it again... :nonod:

its ok bro. Like i said over the phone, just give me a ring then i'll come over to help u.  ;)


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

optoms

  • Guest
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #148 on: December 21, 2006, 11:24:14 PM »
Thank!! You are very helpful :thumbsup:

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #149 on: December 21, 2006, 11:25:37 PM »
Thank!! You are very helpful :thumbsup:

no problem bro.  ;)


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

maddriver

  • Guest
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #150 on: December 24, 2006, 02:59:33 PM »
Hey Bro Corgan.. :D The sound proofing insulator tape is onli $10 for 4 doors..where to find?Rite..Homefix are selling easily 2 to 3 times the price..

Bro,give it a try..no harm ..Thanks for Bro Corgan for organising this..Thumbs up for u and merry christmas to the bros and sista here

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #151 on: December 24, 2006, 03:16:22 PM »
Hey Bro Corgan.. :D The sound proofing insulator tape is onli $10 for 4 doors..where to find?Rite..Homefix are selling easily 2 to 3 times the price..

Bro,give it a try..no harm ..Thanks for Bro Corgan for organising this..Thumbs up for u and merry christmas to the bros and sista here

 :D wah. came all the way here.  :D  Merry christmas and a Happy New yr to u too Benny.  :clap:


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline Driver

  • Cool Engine (0 rpm)
  • Posts: 22
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #152 on: December 24, 2006, 11:15:20 PM »
Bro Corgan
Well said by Bro Maddriver (Benny), good job on the door lining  :thumbsup:,. BTW your Latio very shine and wet. Should post your pic here. Wish you  and all bro & sis a merry christmas and a happy new year.  :smile:

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #153 on: December 24, 2006, 11:27:01 PM »
Bro Corgan
Well said by Bro Maddriver (Benny), good job on the door lining  :thumbsup:,. BTW your Latio very shine and wet. Should post your pic here. Wish you  and all bro & sis a merry christmas and a happy new year.  :smile:

wah. So long nv see u post liao. how's the effect of the lining on urs? You got it done also?  :D Ur ride even wetter than mine la. :D I got some butter wax to try from Benny but like keep raining these few days again.  :(

Anyway, Merry Christmas and a Happy New Year to you too!


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline Driver

  • Cool Engine (0 rpm)
  • Posts: 22
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #154 on: December 25, 2006, 11:07:33 PM »
Out of Town for a while. haven't fix mine yet. Interested to fix the lining on the door rather than frame, neater. You have been a  :thumbsup: diy sifu, very soon will be guru. We need ppl like you  :thumbsup:
 Cheers

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #155 on: December 26, 2006, 12:59:44 AM »
Out of Town for a while. haven't fix mine yet. Interested to fix the lining on the door rather than frame, neater. You have been a  :thumbsup: diy sifu, very soon will be guru. We need ppl like you  :thumbsup:
 Cheers

haha. I just newbie who willing to learn and experiment.  :D or allow others to experiment on mine. Other bros like Vincent and latioblues who did up their own rides are the true sifu  ;) Hope too see you next time at our DIY sessions then.  :thumbsup:


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #156 on: December 27, 2006, 12:01:05 AM »
These are the people who have put their names down and still havent collected. Pls contact me to fix a collection time and place k? 

1. Laguna968 - collecting another day
2. alezis - collecting another day
3. undercover
4. Revin81


These are the people who have allocated their interest. Prices still at $10 

1. teo_jason - 98790334
2. Leapin_Toufu (9-8-5-5-5-1-9-1)
3.
4.
5.


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

revin81

  • Guest
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #157 on: December 28, 2006, 12:47:20 AM »
Hi Corgan, would you be able to install it for me?

Offline corgan

  • Max Torque (4400 rpm)
  • ****
  • Posts: 2,246
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #158 on: December 28, 2006, 01:04:36 AM »
Hi Corgan, would you be able to install it for me?

Hi bro. I believe its simple enough to DIY but i dun mind showing u how to do up one door ;) pls contact me to arrange a place and time to meet.


My ICE journey so far - Pioneer P80RS - Morel Supremo Piccolo Tweeters - Morel Elate Midbass - Butler 475 - OZ vector 3 12" sub - Alpine MRP650 - MIT EXp2 Interconnects

Latioblues

  • Guest
Re: DIY door lining to reduce wind noise: who's interested?
« Reply #159 on: December 28, 2006, 01:22:31 PM »
Hi Corgan, would you be able to install it for me?

You should start charging them $1 for the installation. Consider that as a token of appreciation or just save up for your future experience. :bleh:

Anyway, my experience is that if you intend to stick it on your door itself, try not to stretch it. The rubber strip is elastic but not the sticking tape behind. Part of my lining came off and I need to patch it up with the leftovers.

I am still waiting to do the wheel arc... when you free? can "experiment" again.  :D